logo Raytech

APPELEZ-NOUS
855.904.6565

Distributeurs

header logo 1 header logo 2 header logo 3

DEMA’s kitchen/food service systems are supported with a broad line of parts and accessories built to precise manufacturing tolerances, assuring a “perfect fit” every time and delivering superior durability to lower your total cost of equipment ownership.

Documents PDFDétails
img_pdf

Brochure

Instruction Sheet

Low Level Alarm Sensor Kits

Low Level Alarm

DEMA’S Low Level Alarm is the low level and out-of-products alarm system that can be used as a stand alone unit with virtually any dispenser or as an integral part of DEMA’s Atlas laundry, Titan and Nitro warewash dispensers. Its patent-pending touch-less design isolates electronics from chemicals eliminating the potential for chemical attack plus works with all chemistry regardless of conductivity. Alarm senor wires directly to the Titan or Nitro warewash dispensers for use with up to 3 products or to the alarm base unit Alarm base unit can be used with up to 8 chemicals, can be mounted as a stand alone unit or connected to the Atlas Laundry Dispenser Base unit plugs into standard wall outlet or powers off Atlas control board Alarm sensor can be mounted anywhere in the chemical in take line Sensor has green and red LED for easy out-of-product ID in remote chemical storage areas

Model No. Item Description 84-65-48 Stand Alone Base Unit Base unit up to 8 chemicals. Need to add 1 sensor for every chemical 84-65-49 Atlas Base Unit Base unit for up to 8 chemicals for the Atlas Laundry System. Need to add 1 sensor for each chemcial 84-65-44 Alarm Sensor Sensor with 3/8″ barb for Titan(II), Titan Express(II), Nitro and base units above 84-65-45 Alarm Sensor Sensor with 3/8″ JG for Titan(II), Titan Express(II), Nitro and base units above 84-65-46 Alarm Sensor Sensor with 1/4″ JG for Titan(II), Titan Express(II), Nitro and base units above
img_pdf

Action Gap & Air Backflow Preventers and Proportioners

DEMA offers Action Gap and Air Gap back flow preventers to meet virtually any plumbing requirement. The 16-30 Action Gap backflow preventer attaches to a 1, 2.5 or 4 gpm (4, 10 or 15 L / min.) proportioner to achieve the best flow for the particular application. DEMA’s Air Gap has a built-in proportioner and is available with either 1 or 4 gpm (4 or 15 L / min.) flow rate.

img_pdf

Brochure

Pressure Relief Tee

68-6 Pressure Indicating Tee is designed to protect faucet backflow devices not rated for continuous supply pressure and to virtually eliminate hot cold water cross connection. This device is tested and complies with ASSE 1055-1997 and required by some state and local regulatory agencies. Check local plumbing regulations for back flow and connection requirements. 68-6QD1 Tee with Male Quick Disconnect 68-6QD2 Tee with Male and Female Quick Disconnect.

 

img_pdf

930 Series Chemical Storage Racks

DEMA offers multiple chemical storage racks for 1 gallon (4L) round, 1 gallon (4L) F-Style and 2.5 gallon (10L) containers. Various racks are available for 1-3 chemicals in locking and non-locking configurations. All racks are metal wire and feature a powder coated finish for durability and chemical resistance.

 
Model No.
Stations
Bottle Type
Locking/Non-Locking
930.1R
1
Round ( 1 GAL)
Non-Locking
930.1F
1
F-Style (1 GAL)
Non-Locking
933.1F
1
F-Style (2 1/2 GAL)
Non-Locking
931.2
2
Round (1 GAL)
Locking
930
3
Round (1 GAL)
Non-Locking
931
3
Round (1 GAL)
Locking
img_pdf

Cut Sheet

Barrier Paper

Barrier Paper is a thin protective paper that is installed inside the screen cap before the screen cap is applied to the chemical jar. The piece of barrier paper prevents powdered chemical from escaping through the mesh and reduces the potential for liability as a result of chemical exposure. It is intended to protect the end user from the point when they remove the safety wafer until they invert the jar of encapsulated powder and place it into the Viking Bowl. Barrier Paper is water soluble which means that once it comes in contact with water it will dissolve and then the chemical can escape through the mesh without interference.

img_pdf

Cut Sheet

Screen Caps

There are four different kinds of screen cap available, two different closure types (threaded and locking) and two different mesh sizes (B and N). Every cap has a safety wafer snapped on – this is removed by the end user before the container is inverted into a Viking Bowl. The caps are meant for jugs (also called bottles, jars, and containers) with a 100 millimeter Threaded or Locking neck finish. Screen caps can be used for both encapsulated powder chemicals AND solid chemicals. In the case of solids, they are usually used to prevent large chunks of chemical from falling on the grate and spray nozzle at the bottom of the bowl.

img_pdf

Brochure

Pump Squeeze Tubing

img_pdf

Brackets Cut Sheet

Dip Tubes

Warewash Units Parts List

Drain/Deodorizing Parts List

Viking Bowl Spray Nozzles

Brass Injection Fittings

Check Valves

Detergent Probes

Dish Tank Fittings

Plastic Injection Fittings

Saddle Brackets/Self Tapping Valve

Straight Plastic Injection Fittings

Viking accessoiries